|
The Canon EF-S lens mount is a derivative of the EF lens mount created for a subset of Canon digital single-lens reflex cameras with APS-C sized image sensors. It was released in 2003. Cameras with the EF-S mount are backward compatible with the EF lenses and, as such, have a flange focal distance of 44.0 mm. Such cameras, however, have more clearance, allowing lens elements to be closer to the sensor than in the EF mount. Only Canon cameras released after 2003 with APS-C sized sensors support the EF-S mount. The "S" in EF-S comes from "Small image circle", meaning the lens is designed to provide a small (relative to a normal EF lens) image circle to match the sensor. The smaller mirror used in APS-C cameras also allows optical elements to protrude further into the camera body, which enhances the possibilities for wide angle and very wide angle lenses, enabling them to be made smaller, lighter (containing less glass), faster (larger aperture) and less expensive. Although not all Canon EF-S lenses use this short back focus, they cannot be mounted on DSLRs with sensors larger than APS-C. However, some lenses produced by third-party manufacturers may feature the standard EF mount if they do not require the shorter back focus but only have a small image circle. Such lenses will give noticeable vignetting if used on a 35mm film or full frame sensor cameras. To a lesser degree, vignetting also occurs with APS-H sensor sizes, such as several (now discontinued) cameras of the 1D series. ==Compatibility== The cameras that can use the EF-S mount are: * EOS 7D * EOS 7D Mark II * EOS 20D * EOS 20Da * EOS 30D * EOS 40D * EOS 50D * EOS 60D * EOS 60Da * EOS 70D * EOS 100D/Rebel SL1 * EOS 300D/Digital Rebel * EOS 350D/Digital Rebel XT * EOS 400D/Digital Rebel XTi * EOS 450D/Rebel XSi * EOS 500D/Rebel T1i * EOS 550D/Rebel T2i * EOS 600D/Rebel T3i * EOS 650D/Rebel T4i * EOS 700D/Rebel T5i * EOS 750D/Rebel T6i * EOS 760D/Rebel T6s * EOS 1000D/Rebel XS * EOS 1100D/Rebel T3 * EOS 1200D/Rebel T5 By design, it is physically impossible to mount EF-S lenses on EF-only cameras. This is because the increased proximity of the lens to the sensor means that on full-frame sensor or 35mm film EF cameras the lens itself would obstruct the mirror's movement and cause damage to the lens and/or camera. While it is possible to modify the lens such that the physical obstruction is removed, allowing for mounting to EF mount cameras, the rear of the lens would still obstruct the mirror. An additional reason is that the lenses produce a smaller image circle of even illumination (circle of no vignetting). An EF-S lens alignment mark is indicated by a small white rectangle, whereas the EF employs a small red dot. The lens will insert into the body when the alignment marks on each are matched, and the lens can then be rotated and locked into the operating position. EF-S camera bodies have both EF-S and EF alignment marks, while EF bodies have only EF marks. Some have reported success attaching EF-S lenses to full-frame bodies with the use of an extension tube; however, this does not eliminate the vignetting problem, and also removes the lens's ability to achieve infinity focus. Also, attachment of EF-S lenses on EF bodies can often be accomplished by removing the small plastic ring seen in the photo above. Although vignetting is still an issue, photos can be taken, and infinity focus achieved. This modification comes with caveats, one being that on some lenses, like the EF-S 10-22mm, at the 10mm setting, the element protrudes too far back toward EF mount camera bodies. The 10D, D60, and earlier cameras share the EF-only mount with the full frame EOS camera bodies, and also with the APS-H size EOS camera bodies (1D series prior to the 1D X), despite having a smaller sensor and therefore a smaller mirror. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Canon EF-S lens mount」の詳細全文を読む スポンサード リンク
|